Buying Guide · CNC Angle Lines
How to Read a CNC Angle Line Capacity Table
A capacity table helps you shortlist a CNC angle line, but its biggest number rarely answers the purchase question. The line has to handle the combination of section, material, hole pattern, finished length and output that your drawings call for.
RITEC builds CNC angle lines in our own factory in Jinan, Shandong Province, China. Our spec sheets state each capacity figure per model, with the conditions behind it. This guide explains what each figure means and what to check against your parts.
- Section range, material basis and hole tooling
- Stock length, finished length and cutting
- Speed figures versus real batch output
Built in Jinan
Our own factory
One line
Mark, punch, shear in one continuous process
What This Guide Covers
Each step takes one group of figures from a capacity table and shows how to check it against your drawings.
Check Both Legs, Thickness and the Smallest Section
The section range tells you which angle sizes a model takes, so read both leg widths and the thickness, not only the largest figure. Then check that your smallest section fits as well as your largest.
Send us your angle schedule and we mark which sections fall inside the range of the model we propose.
Check in your angle schedule
Both Legs
Leg widthsAn angle size gives two leg widths and a thickness. Check both legs against the table, and do not assume that a range written for equal angles also covers unequal angles.
Thickness with the Section
CombinationA maximum thickness may apply only to certain leg sizes. Check the thickness that comes with each of your sections, not the two figures one at a time.
Your Smallest Section
Lower limitSupport, clamping and tool access have to work across the whole range you plan to run. Small, thin angles need the same check as the heaviest ones.
Raw Section, Finished Part
GeometryThe table describes the raw section. Holes, notches and cuts change the finished part, so we check your part drawings, not only your section list.
Ask Which Material the Capacity Refers To
A capacity figure is valid for the material it was stated for. Higher-strength steel needs more punching and shearing force, so the same section can sit inside the range in one grade and outside it in another.
Our spec sheets state the material basis next to each figure. Tower and structural angle work often mixes grades in one schedule, so send yours and we confirm each grade against the model we propose.
Find the Strength Basis
Look for the material or strength condition printed next to the section and hole figures. If a table gives none, ask for it before you compare.
Bring Your Own Grades
List every grade you buy, with its thickness and hole sizes. We check each combination instead of stretching one figure across all of them.
Read Test Results Carefully
A test only proves the material and tooling it used. Make sure a test record names the grade, the section and the tools, so it counts as evidence for your parts.
Maximum Hole Diameter Is Not the Whole Hole Specification
The maximum hole diameter is valid only together with a thickness, a grade and the tooling installed. Read the hole rows as one set, then check the hole positions on your drawings against them.
| Figure on the table | What it usually describes | What we confirm for your parts |
|---|---|---|
| Maximum hole diameter | The largest punch for a stated thickness and grade | Your diameters at your thickest section and strongest grade |
| Punches per leg | Tool positions on each leg, not holes made at the same moment | Which punches stay installed and which tool changes your batch needs |
| Punching force | The pressing capacity of the punching unit | The force your hole size, thickness and grade need together |
| Hole positions | Limits for holes near the end, the edge or the heel | Every hole on your drawings, on both legs |
| Hole shapes | The punch shapes the tooling is made for | Each shape your drawings call for |
Maximum hole diameter
The largest punch for a stated thickness and grade
Your diameters at your thickest section and strongest grade
Punches per leg
Tool positions on each leg, not holes made at the same moment
Which punches stay installed and which tool changes your batch needs
Punching force
The pressing capacity of the punching unit
The force your hole size, thickness and grade need together
Hole positions
Limits for holes near the end, the edge or the heel
Every hole on your drawings, on both legs
Hole shapes
The punch shapes the tooling is made for
Each shape your drawings call for
Our line punches both legs of the angle, and we keep force, installed tooling and confirmed hole capability as three separate checks. Where a hole falls outside what punching should do, read our guide to angle punching vs drilling.
Confirm the Part Can Enter and Leave the Machine
A maximum section says nothing about how a short part or the last piece of a stock length gets through the line. Check stock length, finished length, cutting and outfeed against your real drawings.
Our CNC angle line feeds the angle, marks the part number, punches both legs, shears it to length and discharges the finished part in one continuous process. These are the length and handling points we confirm for each project.
| Specification | What to check |
|---|---|
| Raw stock length | Whether loading and feeding suit the lengths you buy |
| Minimum finished length | Whether your shortest member can be held and completed safely |
| Outfeed arrangement | How long and short finished parts are collected |
| Remnant | What material is left after the processing sequence |
| Cutting method | Whether the cut gives the end geometry and condition you need |
| Extra end processing | Which operations need a separate machine |
Raw stock length
Whether loading and feeding suit the lengths you buy
Minimum finished length
Whether your shortest member can be held and completed safely
Outfeed arrangement
How long and short finished parts are collected
Remnant
What material is left after the processing sequence
Cutting method
Whether the cut gives the end geometry and condition you need
Extra end processing
Which operations need a separate machine
Notched ends and milled heels are separate operations. We also build CNC hydraulic angle notching machines and angle steel heel milling machines for that work.
Send Your Section Range and Hole Schedule
Send your angle sizes, grades, hole diameters and stock lengths. We check them against our spec sheets and tell you which model covers your parts and which items need a special configuration.
Compare Offers on the Same Basis
Put your requirements into one matrix and ask every supplier to answer each row in writing. Send it to us and we answer it row by row with our offer.
| Your requirement | What the written answer must state |
|---|---|
| Routine part group | The model, material basis and tooling |
| Largest or strongest combination | The confirmed processing limit and how it will be tested |
| Short or difficult part | How it is held, reached and completed |
| Required marking | The marking method, characters and position |
| Mixed hole pattern | The installed tools and the changeover procedure |
| Requested output | The job list, timing boundary and assumptions |
Routine part group
The model, material basis and tooling
Largest or strongest combination
The confirmed processing limit and how it will be tested
Short or difficult part
How it is held, reached and completed
Required marking
The marking method, characters and position
Mixed hole pattern
The installed tools and the changeover procedure
Requested output
The job list, timing boundary and assumptions
This matrix is a purchasing worksheet, not a machine specification. Keep the written answers with the offer.
Ask What a Performance Figure Actually Measures
Positioning speed, operation time and batch output are three different measures. Ask which one a table quotes and what work it leaves out.
Positioning Speed
- How fast the angle moves between hole positions
- Leaves out punching, shearing and handling
- Useful, but it is not output
Operation Time
- Time for one punching or shearing stroke
- Leaves out feeding, tool changes and checks
- Never multiply it into a daily figure
Batch Output
- Finished parts from a defined job list
- Includes setup, tool changes, handling and checks
- The figure worth comparing
Compare lines on the same drawings, batch quantities and material. Do not combine the best values from separate rows into a condition no machine runs.
When we estimate output for your parts, we say which figures are estimates and how they can be checked. For a full tower shop, see how we balance angle and plate work in transmission tower fabrication equipment.
Common Capacity Table Questions
Short answers to questions buyers ask when they compare angle line spec sheets. If yours is not here, ask Henry.
Does a model name tell me the maximum angle size?
No. Treat the model name as an identifier only. Read the current spec sheet and its conditions, and never work out a capacity from the digits in a model code.
Does the largest hole diameter apply at the maximum thickness?
Not automatically. The largest hole and the thickest section may each be valid only on their own. We confirm the exact combination of grade, thickness, hole size and tooling for your parts.
Can two lines with the same maximum section have different output?
Yes. Their configurations and the work between operations can differ a lot. Compare a defined job list, not one shared capacity figure.
Does an angle line capacity table cover connection plates?
No. Tower and structural connection plates are processed on separate machines. We build CNC plate drilling machines that drill, tap and chamfer or countersink plate holes, and hydraulic plate punching machines for punched plates.
Can you check the spec tables I am comparing?
Yes. Send the tables with the unclear items marked, plus your section range, grades and hole details. We tell you which of your parts our proposed line covers and under what conditions.
What should I do after shortlisting?
Send representative and limiting parts, ask for a confirmed requirement matrix and agree the sample checks before you finalise the technical scope.
Compare Your Parts Against Our Spec Sheet
Send the details listed here, add any spec tables you are comparing and mark the unclear items. We turn nominal capacities into a clear list of the parts our proposed line will complete.
Or email cncmachinery@costergroup.cn
Send us these details
- Section range
- Material grades
- Hole diameters and positions
- Stock lengths
- Shortest finished part
- Marking requirement
- Output target
- Spec tables you are comparing